Currently Out of Stock until 12/16
Melt Point: 122 F
Container Candle Soy Wax
EcoSoya CB-135 has excellent adhesion to containers without preheating, requires only one pour, has an excellent scent throw with both fragrances and essential oils and a creamy white appearance with some potential to bloom (white frosting) when using dyes.
EcoSoya CB-135 is made from pure 100% soybeans and carefully selected botanical oils. Candles made with CB-135 have a soft creamy appearance and a smooth flat top surface and ships well in all climates.
CB-135 is dermatology tested and perfect for massage candles.
EcoSoya CB-135 Soy wax is available in 10 lb bags or 50 lb cases.
Containers and jars should be clean and at ambient temperature. No pre-heating is necessary.
Most dyes (powder, liquid, chips, blocks, etc.) work with CB-135. To achieve better color depth, use about 30% more dye. When using powder dyes, heat the wax to 190°F (87.8°C), add the dye, and mix until dissolved. Powder dyes may also be dissolved in fragrances and then added to the melted wax (be sure the dye has dissolved completely before adding). *When using powder dyes dissolved in fragrance, liquid dyes, color blocks, chips or no dye, heat the wax to155°F (68.3°C).
Fragrances / Essential Oils
Many fragrances and essential oils work in CB-135, especially those designed for soy wax in general. Recommended maximum scent load is about 12%. To minimize scent loss, add scent prior to pouring but at a wax temperature no less than 135°F (57.2°C). Accommodate for temperature drop due to the addition of the cooler scent when targeting the pour temperature. Optimum hot scent throw is achieved with a full diameter burn pool at a depth of ¼ to ½ inch (0.6 to 1.3 cm). Some scents may react poorly causing bleed, objectionable frosting, or poor flame quality. Try a different scent or manufacturer to correct that occurrence.
CB-135 requires larger wicking than paraffin. Wicks such as paper cored, cotton cored or metal cored should be avoided as they tend to cause sooting and carbon build-up. A general rule of thumb: have a full burn pool of ¼ to ½ inch (0.6 to 1.3 cm) deep, from side to side, in approximately the same number of hours for every inch (2.5 cm) of the container diameter.
Example: An Apothecary jar with a diameter of 4 inches (10.2 cm) should achieve a burn pool depth of ¼ to ½ inch (0.6 to 1.3 cm), side to side, within about 4 hours.
The following table, listed in no particular order, suggests a starting point for the type and size of wicks to begin testing with; note that adjustments may be needed. Keep wicks trimmed to ¼ inch (0.6 cm). If you experience poor flame quality or stability, try a different type of wick. Test burning should be done after the candle has had a chance to set up and cure for 48 hours after pouring.
Initial Wick Suggestions to Begin Testing
Feel free to try other types and sizes of wicks as needed
1 to 2 inches
(2.5 to 5.1 cm)
|CD: 5||Eco: 2 |
Flat Braid: 18
Square Braid: #4/0
| || || || |
2 to 3 inches
(5.1 to 7.6 cm)
|CD: 12||Eco: 6|
|Flat Braid: 30|
Square Braid: #1
| || || || |
3 to 4 inches
(7.6 to 10.2 cm)
|CD: 20||Eco: 14|
|Flat Braid: 60|
Square Braid: #3 or #4
| || || || |
4 inches and larger
(10.2 cm & larger)
Typically requires double wicking. Try using 2 wicks spaced
1 inch (2.5 cm) apart.
When using all dye, except for powdered or un-dyed CB-135, melt the wax to a minimum of 155°F (68.3°C) under gentle agitation to promote even heating and thorough mixing. For powder dyes, heat the wax to 190°F (87.8°C) to ensure the dye dissolves. Temporary high temperatures such as 190°F (87.8°C) have no adverse effect if cooled quickly. Higher temperatures, in excess of 190°F (87.8°C), may cause the wax to discolor. Allow the wax to cool to the desired pour temperature.
It is typical for wax to solidify at the beginning of the pour during its first contact with the container. CB-135 should have a pour temperature high enough so that when the container is full, the initial solidified wax has re-melted. The temperature should not be so high that the liquid wax sits more than 30 minutes before starting to solidify.
Pour temperatures will vary according to container type and size, fragrance and dye, and the effects you want to achieve. CB-135 can be poured as low as 100° F (37.8° C) if the wax is kept in motion (constant mixing) until poured. Lower pour temperatures may help to reduce frosting while producing a smooth top and good adhesion.
There is a difference in cooling rates for different container configurations. Cooling too quickly or too slowly can cause concaving and/or frosting. Large jars such as the apothecary configurations and large candles above 8 oz (237 ml) in size cool slower and require lower pour temperatures, about 125°F (51.7°C). Smaller candles (less than 8 oz (237 ml)) and metal/tin containers cool fast, requiring a higher pour temperature of about 155°F (68.3°C). If difficulties are experienced with your pour temperatures, try a lower or higher temperature in increments of 10°F (6°C).
When candles are poured at a lower temperature (about 110°F (43.3°C)), add the scent at a higher temperature (about 140°F (60°C)) and allow the wax to cool to the desired pour temperature.
Pour temperatures should be checked and confirmed according to seasonal changes.
Cool undisturbed candles at an ambient temperature of 70° F (21.1°C). The containers should be about 1/2 inch (1.3 cm) apart to allow air circulation for even cooling. The container should remain open during cooling for at least 24 hrs (large candles may require longer times). Slower cooling will encourage container adhesion while quicker cooling will encourage container pull away. CB-135 is designed to adhere to the glass and should be encouraged to do so. Candles should be allowed to sit undisturbed for 48 hours before test burning.